CLIP-IT® installation instructions
How to use 3 mm stone clips for 30–40 mm material.
Use 30 mm Stone & Paver Wedges below 35 mm and Regular Wedges from 35–40 mm. The matching wedge holds adjoining stone or paver edges in alignment while the adhesive or bedding material cures.
- Grout joint
- 3 mm
- Material thickness
- 30–40 mm
- Clip colour
- Light grey
Before you start
Prepare for a clean installation.
Check the base and layout
Confirm the stone, tile or paver is 30–40 mm thick and the planned grout joint is 3 mm. Prepare a clean, flat, level base for the chosen installation.
Use the right adhesive
Choose adhesive or bedding material suited to the installation. Apply it with the appropriate trowel, following the manufacturer’s instructions.
Have compatible wedges ready
For material from 30 mm up to below 35 mm, use 30 mm Stone & Paver Wedges. For 35–40 mm material, including exactly 35 mm, use Regular Wedges.
Using the product
Place. Tighten. Remove.
Follow the three stages for your clip and compatible wedge.

Place the clips and adjoining pieces
Set the first piece firmly, then slide the clip base under its exposed edge. Keep the upright part of the clip at the joint.
Position the adjoining piece against the clip so the base sits beneath both edges. Check joint spacing as you continue.

Insert and tighten the wedges
Push the wedge recommended for your material thickness through the clip opening to hold adjoining edges in alignment.
For material from 30 mm up to below 35 mm, use 30 mm Stone & Paver Wedges. For 35–40 mm material, including exactly 35 mm, use Regular Wedges. Check adjoining surfaces as you tighten.
Example shown: 35 mm material with a Regular Wedge.
Let the installation cure, then remove
Wait until the adhesive or bedding material has cured, following the manufacturer’s curing instructions.
Remove the cured clips along the grout line. The DE-CLIP-IT Hammer can knock these larger clips off, but its slotted end does not fit over them. Recover the wedges for reuse.
Complete the setup
Complete your setup.
Use the compatible CLIP-IT® products for this guide.

Regular Wedges
Recommended with this clip for 35–40 mm material, including exactly 35 mm.

30 mm stone & paver wedges
Recommended with this clip for material from 30 mm up to below 35 mm.


DE-CLIP-IT Hammer
Hammer action only on these larger clips; the slot does not fit.
A few useful answers
Get the details right.
Material thickness, wedge fit and clip removal.
What do 3 mm and 30–40 mm mean?
3 mm is the grout joint spacing. 30–40 mm is the thickness of the stone, tile or paver the clip is designed to suit.
Which wedge should I choose?
For material from 30 mm up to below 35 mm, use 30 mm Stone & Paver Wedges. For 35–40 mm material, including exactly 35 mm, use Regular Wedges. These are the recommended choices; some thicknesses can fit both wedges. Thinner material leaves a larger gap beneath the top of the clip, so it needs a taller wedge.
Does the hammer slot fit these clips?
No. The slotted end does not slide over 3 mm 30–40 mm Stone Clips. Use the tool as a hammer to knock off cured clips along the joint.
When can I remove the clips?
After the adhesive or bedding material has cured. Follow its manufacturer’s curing instructions; there is no single curing time for every product and job.
Why is a clip not breaking cleanly?
Excess adhesive around the clip legs can interfere with removal. Keep that area clear during laying, allow curing, and remove along the grout line. Contact CLIP-IT® if a clip remains stuck.
Can the wedges be reused?
Yes. Recover the compatible wedges after clip removal and keep them for the next installation. The clips are designed to break at the base during removal.
Talk to the people who make it
Need a hand with your installation?
Tell the CLIP-IT® team your material thickness, joint width and what is happening so we can help you check the setup.


